Raymond Mill solution

Professional ingenuity, high efficiency and low consumption Raymond mill, calcium hydroxide mill

Yiwen tells you what Raymond mill is

Raymond mill is a high-efficiency closed-circuit high-fine pulverizing equipment suitable for small and medium-sized mining, chemical industry, building materials, metallurgy, refractories, pharmacy, cement and other industries. It is a new pulverizer instead of ball mill to process powder. Its output and energy consumption meet the national standard, ranking the domestic advanced level, and is highly praised by users in various industries. 1. During the working process of the mill, there shall be fixed personnel to take care of it. The operator must have certain technical knowledge and level. The user must carry out technical training for the operation, maintenance, electrical and other relevant personnel before the installation of the mill according to the specific conditions of the factory, and can only operate after they are familiar with the performance and principle of the machine.
2. The user unit shall formulate equipment maintenance and safety system according to the use of the mill to ensure the long-term safe operation of the mill.
3. Except that the upper part of the main shaft of some models adopts sliding bearing, the other transmission parts adopt rolling bearing. Therefore, it must be operated under good lubrication conditions, otherwise the bearing will be damaged and the service life will be shortened. See the lubrication system table for specific refueling time and types of grease.
4. The metal block is strictly prohibited to enter the machine. If it is found, stop the machine immediately and take it out, otherwise the grinding roller and ring will be damaged.
5. The feeding shall be uniform and not more or less. Too much feeding will block the air duct and reduce the output, which is easy to burn the motor. Too little feeding will also reduce the output. Refer to table 1 for feed particle size. It is strictly prohibited to add large materials into the machine.
6. Air volume adjustment: the air volume control valve located on the air inlet pipe of the fan is generally opened to the maximum position and adjusted appropriately according to the fineness and output requirements. Small air volume and high fineness. However, it should be noted that the air volume is too small and it is easy to precipitate materials in the air duct under the main engine. Please adjust it appropriately. The regulating valve located on the dust discharge pipe at the outlet of the fan can be adjusted to ensure that there is no dust at the feed inlet during normal operation.
7. Fineness adjustment: according to the size of the material, the hardness, moisture content and specific gravity are different, and the processing thickness is also different. The analyzer above can be adjusted, with high speed, high fineness, low speed and low fineness. If the fineness is improved, the output will be reduced accordingly. If the requirements are not met, the air volume and speed of the fan shall be debugged, which can be flexibly mastered by the user.
8. The scrapping limit of grinding roller and ring, and the remaining minimum wall thickness shall not be less than 10mmm.
9. When the machine is shut down, stop feeding first, and the main machine still continues to operate to continue grinding the residual materials. After about one minute, turn off the main machine motor and analyzer motor to stop grinding, and then stop the fan motor to blow away the residual powder.
The machine adopts the advanced structure of similar foreign products and is updated and improved on the basis of large Raymond mill. The equipment has the advantages of high efficiency, low power consumption, small floor area and small one-time investment. The grinding roller is tightly rolled on the grinding ring under the action of centrifugal force. Therefore, when the grinding roller and grinding ring are worn to a certain thickness, the output and fineness of finished products will not be affected. The replacement cycle of grinding roller and grinding ring is long, so as to eliminate the disadvantage of short replacement cycle of vulnerable parts of centrifugal crusher. The air separation air flow of the machine is circulating in the fan – shell grinding – cyclone separator – fan, so it has less dust than the high-speed centrifugal crusher, the operation workshop is clean and the environment is pollution-free.
Purpose and scope of application:
This product is applicable to barite, calcite, potassium feldspar, talc, marble, limestone, dolomite, fluorite, lime, activated clay, activated carbon, bentonite, kaolin, cement, phosphate rock, gypsum, glass, manganese ore, titanium ore, copper ore, chrome ore, refractory, thermal insulation material, coal coke, pulverized coal, carbon black, pottery, bone powder, titanium dioxide, iron oxide For non flammable and explosive minerals such as quartz with Mohs hardness no more than 7 and humidity less than 6%, high-fine powder processing of more than 300 materials in chemical, construction and other industries, the particle size of finished products can be adjusted arbitrarily within the range of 80-325 mesh, and some materials can reach 600 mesh at most.

Customer site

Hengda specializes in Raymond machines for more than 20 years, specializing in customized high-efficiency and low-consumption grinders.

Raymond mill Factory In China